Boat › Hull and deck
The hull is what keeps the water out, so it pays to look after it. These topics cover finding where a leak is getting in, patching and welding an aluminium hull, repairing a rusty steel one, getting rid of rust, the coating system that protects steel, and antifouling the hull and propeller to keep the growth off. Up top, there's fitting a bimini for shade.
Checking a second-hand boat before you buy it
Open ›
Work out what you need the boat for, then check the hull, trailer and motor, do a compression test and a run on the water, and make sure there's no money owing before you hand over yours.
Restoring Renko, a rusty steel trawler, from 2019 to 2025
Open ›
In January 2019 I bought a cheap, rusty 9 metre steel trawler and spent the next few years restoring it, on the hardstand and on the mooring. The videos follow the whole job in order, from buying it to painting it in Bundaberg, and the touch-ups since.
Finding where water is getting into a boat
Open ›
A boat that keeps taking on water has a leak somewhere. I go through ways to find it, using water, air or light, and check the usual suspects first.
Repairing holes and cracks in an aluminium hull
Open ›
Holes and cracks in an aluminium boat can be fixed without welding, with a riveted plate and sealant, or welded with TIG or even a stick welder.
Repairing a rusty steel hull
Open ›
Rust in a steel boat can be fixed in many ways, from pad welding a pit to cutting out the whole back deck. I go through them on the trawler, and measure the plates with an ultrasonic tester.
Removing rust with converter, wet blasting or electrolysis
Open ›
Rust has to be dealt with before you paint. I use a rust converter, set up a DIY wet blaster, and clean rusty parts in an electrolysis bath.
Antifouling the hull and propeller
Open ›
Antifoul keeps weed and barnacles off the bottom and usually needs redoing every year. I antifoul an aluminium boat and a steel trawler, and coat a propeller with Prop Shield.
Blasting, priming and coating a steel hull
Open ›
A steel hull needs a coating system that keeps moisture off the metal. I talk through epoxy primer, barrier coats and polyurethane with Dave from Altex, and coat the trawler.
Bonding a steel hull and testing the anodes
Open ›
On a steel boat I bond battery negative to the hull at one point only, test it with a multimeter, then use a silver half-cell to check the hull has the right amount of anode protection.
Adding a bimini cover to a small boat
Open ›
A bimini keeps the rain and sun off. I put a four-bow bimini kit together and fit it to an aluminium boat, working out where it goes so you can still get in and out, and build a fixed aluminium solar awning for my trawler.
Hauling out and making hardstand props
Open ›
Time on the hardstand is expensive, so plan for it. I make six pivoting-head boat stands from Acrow props, find out what a marina will let you do, and get the parts and tools ready before the haul out.
Repairing a timber hull
Open ›
Timber boats suffer from rot, borer and failing caulking. The shipwrights rebuilding a timber trawler explain replacing ribs and planks and recaulking, and the owner of a 1937 yacht shows how she's replacing its caulking and planks.
Working with epoxy and fibreglass
Open ›
Epoxy glues, fills and seals, and with fibreglass it makes a strong patch. I cut out deck rot and glue in new ply, fill cracks and gouges, glass over a hole, and show how I mix, thicken and wet out epoxy.
Replacing a bow tow eye
Open ›
A tow eye takes the mooring loads as well as towing, and an aluminium one wears thin. I cut off a worn one and bolt on a stainless U-bolt, bedded in sealant and kept apart from the aluminium.
Replacing a perspex windscreen panel
Open ›
A broken perspex windscreen panel can be replaced without special tools. We make a template from the broken pieces, bend the new perspex warm from a barbecue, and fit it into the frame.
